How to torque a Briggs and Stratton head?
Q. I fixed a stuck valve on a 5 hp Briggs and Stratton motor and I would like to know what to torque the head bolts to. Anybody know this? I am guessing about 20. The stare pattern I am aware of, the number is all I need. I think everyone has given me a good idea. Thanks.
Asked by Rahz - Thu Mar 12 13:21:13 2009 - - 5 Answers - 1 Comments
A. 5 hp briggs If 5/16" head bolts torque 25 Ft/Lb if Commercial version with 3/8" head bolts torque to 35 Ft Lbs. In either case follow a criss-cross rotating pattern first gently snugging the bolts, then tightening to 3/5ths of the final torque, finally tightening them to full torque and then torque at spec one more time.
Answered by krazybob613 - Thu Mar 12 14:35:35 2009
Q. I fixed a stuck valve on a 5 hp Briggs and Stratton motor and I would like to know what to torque the head bolts to. Anybody know this? I am guessing about 20. The stare pattern I am aware of, the number is all I need. I think everyone has given me a good idea. Thanks.
Asked by Rahz - Thu Mar 12 13:21:13 2009 - - 5 Answers - 1 Comments
A. 5 hp briggs If 5/16" head bolts torque 25 Ft/Lb if Commercial version with 3/8" head bolts torque to 35 Ft Lbs. In either case follow a criss-cross rotating pattern first gently snugging the bolts, then tightening to 3/5ths of the final torque, finally tightening them to full torque and then torque at spec one more time.
Answered by krazybob613 - Thu Mar 12 14:35:35 2009
How do I fix a briggs and stratton 5hp that wont keep running unless I keep pumping the primer?
Q. I have a briggs and stratton 5 HP engine that wont keep running unless I keep pumping the primer 30 or so times after after it starts. After pumping the primer it will run fine. What do I have to do to fix this?
Asked by Burt - Wed Feb 3 21:17:20 2010 - - 4 Answers - 0 Comments
A. Sounds like the carburetor is having trouble getting the gas to the engine. I would suggest that you properly clean the carb and put in a rebuild kit.
Answered by renpen - Wed Feb 3 21:47:34 2010
Q. I have a briggs and stratton 5 HP engine that wont keep running unless I keep pumping the primer 30 or so times after after it starts. After pumping the primer it will run fine. What do I have to do to fix this?
Asked by Burt - Wed Feb 3 21:17:20 2010 - - 4 Answers - 0 Comments
A. Sounds like the carburetor is having trouble getting the gas to the engine. I would suggest that you properly clean the carb and put in a rebuild kit.
Answered by renpen - Wed Feb 3 21:47:34 2010
how do you start a 18Hp Briggs, 4 cycle engine without a starter?
Q. The Briggs is on a lawn tractor and runs but the starter died and cost to much to replace. So if you have any ideas or know how to start it please tell me.
Asked by Aaron P - Wed Dec 12 16:59:23 2007 - - 4 Answers - 0 Comments
A. remove the cover over the fly wheel, take the screen out, put cover back on, find a socket that will fit the nut on the flywheel, buy a drill adaptor that will fit the socket, 1/4 " 3/8 "drive, and will fit into a drill, turn key on put in park or have some one sit in the seat, spin it over with the drill till it starts, have a 17-1/2 hp i do that to,
Answered by William B - Wed Dec 12 18:23:44 2007
Q. The Briggs is on a lawn tractor and runs but the starter died and cost to much to replace. So if you have any ideas or know how to start it please tell me.
Asked by Aaron P - Wed Dec 12 16:59:23 2007 - - 4 Answers - 0 Comments
A. remove the cover over the fly wheel, take the screen out, put cover back on, find a socket that will fit the nut on the flywheel, buy a drill adaptor that will fit the socket, 1/4 " 3/8 "drive, and will fit into a drill, turn key on put in park or have some one sit in the seat, spin it over with the drill till it starts, have a 17-1/2 hp i do that to,
Answered by William B - Wed Dec 12 18:23:44 2007
How many personality types are there in a Myers Briggs personality test?
Q. How many different combination of personalities are there in the Myers Briggs personality test? It's the one that assigns you with a four-letter code like ENFP or something. Thanks for any help!
Asked by Luvit - Thu Feb 25 16:14:18 2010 - - 2 Answers - 0 Comments
A. 16 personality types. 4 temperaments- NF, NT, SP, SJ There are four personalities within each temperament (i.e. NF= INFP, ENFP, INFJ, ENFJ) But, there are 8 preferences, and all used in different orders and projection. (i.e. ENFP & ENTP's both have dominant Extraverted Intuition, even though they are different temperament types)
Answered by Thelistener - Sat Feb 27 02:09:46 2010
Q. How many different combination of personalities are there in the Myers Briggs personality test? It's the one that assigns you with a four-letter code like ENFP or something. Thanks for any help!
Asked by Luvit - Thu Feb 25 16:14:18 2010 - - 2 Answers - 0 Comments
A. 16 personality types. 4 temperaments- NF, NT, SP, SJ There are four personalities within each temperament (i.e. NF= INFP, ENFP, INFJ, ENFJ) But, there are 8 preferences, and all used in different orders and projection. (i.e. ENFP & ENTP's both have dominant Extraverted Intuition, even though they are different temperament types)
Answered by Thelistener - Sat Feb 27 02:09:46 2010
What is wrong with my briggs and stratton engine?
Q. i just put new rings and gaskets in my 1971 2 1/2 horespower briggs and stratton and now when i give it throttle it dies, any suggestions?
Asked by Shindermouse - Sun Jun 8 22:35:12 2008 - - 3 Answers - 0 Comments
A. Fuel/air mix? Running too rich, and then flooding?
Answered by River 2 Electric Boogaloo - Sun Jun 8 22:43:42 2008
Q. i just put new rings and gaskets in my 1971 2 1/2 horespower briggs and stratton and now when i give it throttle it dies, any suggestions?
Asked by Shindermouse - Sun Jun 8 22:35:12 2008 - - 3 Answers - 0 Comments
A. Fuel/air mix? Running too rich, and then flooding?
Answered by River 2 Electric Boogaloo - Sun Jun 8 22:43:42 2008
How do you check timing on briggs engine?
Q. My 15.5 Briggs backfires when cranking. The engine usually cranks and runs fine after it starts. Any suggestions ?
Asked by barryas1 - Sun Apr 4 21:39:46 2010 - - 1 Answers - 0 Comments
A. To check the timing, you will have to take the blower housing off, and remove the flywheel nut. There is a key that holds the flywheel in place with the crankshaft. If this is a riding mower, it would be a very rare occurrence to shear the key. More than likely, you have a valve problem. If OHV the valves may need adjustment. If not, you may have a worn lobe on the cam.
Answered by Frankie - Sun Apr 4 21:47:28 2010
Q. My 15.5 Briggs backfires when cranking. The engine usually cranks and runs fine after it starts. Any suggestions ?
Asked by barryas1 - Sun Apr 4 21:39:46 2010 - - 1 Answers - 0 Comments
A. To check the timing, you will have to take the blower housing off, and remove the flywheel nut. There is a key that holds the flywheel in place with the crankshaft. If this is a riding mower, it would be a very rare occurrence to shear the key. More than likely, you have a valve problem. If OHV the valves may need adjustment. If not, you may have a worn lobe on the cam.
Answered by Frankie - Sun Apr 4 21:47:28 2010
How do you know if you have a stuck valve on your briggs and stratton engine?
Q. It's a 16hp briggs and stratton intek OHV engine. How do I test to see if the valves are stuck? there is no compression i just want to make sure its a stuck valve.
Asked by Brian Paul - Mon Jul 19 23:44:02 2010 - - 4 Answers - 0 Comments
A. On the front of the engine is a cover with four bolts. Take off the cover and have someone turn the engine over for you. You should see the valves moving (opening and closing). If they don't move when the valve springs go up and down then you have a valve problem. XX
Answered by tonybradburyuk - Tue Jul 20 12:32:02 2010
Q. It's a 16hp briggs and stratton intek OHV engine. How do I test to see if the valves are stuck? there is no compression i just want to make sure its a stuck valve.
Asked by Brian Paul - Mon Jul 19 23:44:02 2010 - - 4 Answers - 0 Comments
A. On the front of the engine is a cover with four bolts. Take off the cover and have someone turn the engine over for you. You should see the valves moving (opening and closing). If they don't move when the valve springs go up and down then you have a valve problem. XX
Answered by tonybradburyuk - Tue Jul 20 12:32:02 2010
What would cause a briggs and strattan not to get spark?
Q. I have a 18.5hp twin cyclinder briggs and strattan engine on a yard machine riding mower that dont have any spark. What could be the problem? I checked and cleaned all the rust from the magneto and fly wheel
Asked by Jay80 - Sun May 2 09:37:38 2010 - - 5 Answers - 0 Comments
A. I had to replace 2 coils on twin cyl. Briggs 18 hp motors in 4 years of use. Use a business card when you set the gap, works perfect. They cost around $60. that was a couple of years ago.
Answered by Chuck - Sun May 2 10:29:22 2010
Q. I have a 18.5hp twin cyclinder briggs and strattan engine on a yard machine riding mower that dont have any spark. What could be the problem? I checked and cleaned all the rust from the magneto and fly wheel
Asked by Jay80 - Sun May 2 09:37:38 2010 - - 5 Answers - 0 Comments
A. I had to replace 2 coils on twin cyl. Briggs 18 hp motors in 4 years of use. Use a business card when you set the gap, works perfect. They cost around $60. that was a couple of years ago.
Answered by Chuck - Sun May 2 10:29:22 2010
How to change oil in Briggs & Stratton lawnmower?
Q. i have a 5.25hp/21 inch briggs & stratton self-propelled lawn mower. I need to find out how to change the oil. It has a straight pipe that goes straight to the mower
Asked by tgrant60133 - Wed May 24 23:58:52 2006 - - 8 Answers - 0 Comments
A. Thats the dipstick, yes you can drain the oil out there, get a drain pan, take the dipstick out, tip the mower over carefully, and drain it. This doesn't get all the oil out though, there's a plug at the bottom of the engine (under the deck) that you put a ratchet (without the socket) into, lifting them up on blocks works for me, slip a container underneath, take the drain plug out and let the oil drain till it stops, put the plug back in tight. NOW, the engine takes 20 ounces of oil maximum... not a whole quart... if you still have the original 18 ounce oil bottle that came with it, fill that up with any name brand HD-30 weight. Thats a high detergent straight 30 above 40 degrees F. Use 5w-30 or 10w-30 conventional below 40. OR use a 5w-3 [cont.]
Answered by 572ci. - Thu May 25 22:10:07 2006
Q. i have a 5.25hp/21 inch briggs & stratton self-propelled lawn mower. I need to find out how to change the oil. It has a straight pipe that goes straight to the mower
Asked by tgrant60133 - Wed May 24 23:58:52 2006 - - 8 Answers - 0 Comments
A. Thats the dipstick, yes you can drain the oil out there, get a drain pan, take the dipstick out, tip the mower over carefully, and drain it. This doesn't get all the oil out though, there's a plug at the bottom of the engine (under the deck) that you put a ratchet (without the socket) into, lifting them up on blocks works for me, slip a container underneath, take the drain plug out and let the oil drain till it stops, put the plug back in tight. NOW, the engine takes 20 ounces of oil maximum... not a whole quart... if you still have the original 18 ounce oil bottle that came with it, fill that up with any name brand HD-30 weight. Thats a high detergent straight 30 above 40 degrees F. Use 5w-30 or 10w-30 conventional below 40. OR use a 5w-3 [cont.]
Answered by 572ci. - Thu May 25 22:10:07 2006
What is the normal labor charged per hour for rebuilding an 8hp briggs and how many hours would you charge for
Q. I'm in a Small engines class at my high school and need to know how much I should charge for rebuilding an engine. It's an 8hp Briggs.
Asked by Mr.Steven - Fri Apr 25 12:41:59 2008 - - 2 Answers - 0 Comments
A. I'd consider cutting your costumer's a little slack when beginning your business as your good work causes people to talk. Under cut the big dealers in town so people know you willing to earn their business. Keep in mind the big boys have access to tough to get parts at discounted costs and they sell them to their costumer's at retail cost plus their overhead items like taxes, insurance, building overhead, tooling costs, workers salaries and owners profits. You need to be entirely truthful with your client's as you don't really know from the outside what a motor needs. If it's an old point ignition motor or a complete carburetor cleaning it's straight forward. Where the trouble begins is if the cylinder needs boring and honing for a new… [cont.]
Answered by Country Boy - Fri Apr 25 13:24:32 2008
Q. I'm in a Small engines class at my high school and need to know how much I should charge for rebuilding an engine. It's an 8hp Briggs.
Asked by Mr.Steven - Fri Apr 25 12:41:59 2008 - - 2 Answers - 0 Comments
A. I'd consider cutting your costumer's a little slack when beginning your business as your good work causes people to talk. Under cut the big dealers in town so people know you willing to earn their business. Keep in mind the big boys have access to tough to get parts at discounted costs and they sell them to their costumer's at retail cost plus their overhead items like taxes, insurance, building overhead, tooling costs, workers salaries and owners profits. You need to be entirely truthful with your client's as you don't really know from the outside what a motor needs. If it's an old point ignition motor or a complete carburetor cleaning it's straight forward. Where the trouble begins is if the cylinder needs boring and honing for a new… [cont.]
Answered by Country Boy - Fri Apr 25 13:24:32 2008
How to rebuild the carb on a 5 hp Briggs and Stratton?
Q. Any sites or info on rebuilding the carb on my sons go cart would be appreciated...Engine is a 5 horse Briggs and Stratton...Thanks
Asked by mike m - Wed Sep 19 02:32:09 2007 - - 3 Answers - 0 Comments
A. Youd need the motor numbers off the flywheel shroud/engine block - a local tractor parts place can get a 'parts kit' for it - including gaskets, o rings, sometimes a float, needlevalve- ect, usually runs in the $20-30 range. Heres a parts breakdown diagram site - look up motor numbers under briggs & stratton :
Answered by The Kidd - Wed Sep 19 08:14:07 2007
Q. Any sites or info on rebuilding the carb on my sons go cart would be appreciated...Engine is a 5 horse Briggs and Stratton...Thanks
Asked by mike m - Wed Sep 19 02:32:09 2007 - - 3 Answers - 0 Comments
A. Youd need the motor numbers off the flywheel shroud/engine block - a local tractor parts place can get a 'parts kit' for it - including gaskets, o rings, sometimes a float, needlevalve- ect, usually runs in the $20-30 range. Heres a parts breakdown diagram site - look up motor numbers under briggs & stratton :
Answered by The Kidd - Wed Sep 19 08:14:07 2007
Can a 14 hp briggs twin replace a 12hp tecumseh ohv?
Q. Hi have a craftsman mower with a blown engine but the rest is ok so I want to replace the engine with a motor from a murray rider. But I just realized that the motor is a tecumseh engine. So can a briggs and stratton 14 hp twin cylinder align with the mount holes of a 12 hp tecumseh single cylinder ohv?
Asked by Black Fawk Down - Fri Nov 13 14:07:38 2009 - - 6 Answers - 0 Comments
A. the shaft has to be the same size
Answered by pickmefirstplz - Fri Nov 13 15:27:29 2009
Q. Hi have a craftsman mower with a blown engine but the rest is ok so I want to replace the engine with a motor from a murray rider. But I just realized that the motor is a tecumseh engine. So can a briggs and stratton 14 hp twin cylinder align with the mount holes of a 12 hp tecumseh single cylinder ohv?
Asked by Black Fawk Down - Fri Nov 13 14:07:38 2009 - - 6 Answers - 0 Comments
A. the shaft has to be the same size
Answered by pickmefirstplz - Fri Nov 13 15:27:29 2009
How can my Myers-Briggs results help me in college and in the future?
Q. I took the Myers-Briggs Type Indicator test and scored ISFJ. How can I use these results to help me in college and in choosing a career?
Asked by kuf99ver3 - Mon Feb 9 15:48:56 2009 - - 2 Answers - 0 Comments
A. The Myers-Briggs test tells you your unconscious preferences. You prefer introversion, sensing, feeling, and judging. But really, the best way to pick a major/career is through your conscious preferences. What do you like to do? What are you good at? Those should be your main questions. That said, ISFJ suggests you might enjoy a career like carpentry, welding, or architecture.
Answered by Marcus - Mon Feb 9 15:53:34 2009
Q. I took the Myers-Briggs Type Indicator test and scored ISFJ. How can I use these results to help me in college and in choosing a career?
Asked by kuf99ver3 - Mon Feb 9 15:48:56 2009 - - 2 Answers - 0 Comments
A. The Myers-Briggs test tells you your unconscious preferences. You prefer introversion, sensing, feeling, and judging. But really, the best way to pick a major/career is through your conscious preferences. What do you like to do? What are you good at? Those should be your main questions. That said, ISFJ suggests you might enjoy a career like carpentry, welding, or architecture.
Answered by Marcus - Mon Feb 9 15:53:34 2009
What is the briggs n stratton number of the governor for this model number engine.?
Q. Model 280777 Type 0691-E1 Code 020604ZD I also need a crankcase gasket briggs number for this engine also. Where can i find pdf files for briggs small engines.
Asked by BigBlackDog - Tue Jul 13 18:24:02 2010 - - 1 Answers - 0 Comments
A. It might be better to log in to the Briggs and Stratton website.They seem to have a pretty good database available.
Answered by wildmanny2 - Tue Jul 13 20:22:44 2010
Q. Model 280777 Type 0691-E1 Code 020604ZD I also need a crankcase gasket briggs number for this engine also. Where can i find pdf files for briggs small engines.
Asked by BigBlackDog - Tue Jul 13 18:24:02 2010 - - 1 Answers - 0 Comments
A. It might be better to log in to the Briggs and Stratton website.They seem to have a pretty good database available.
Answered by wildmanny2 - Tue Jul 13 20:22:44 2010
Who can I contact regarding Briggs Ranch Timeshare lawsuit?
Q. My husband and I purchased a timeshare at Briggs Ranch in San Antonio 3 yrs ago and have been paying for it monthly. Last week we found out that the timeshare was never completed and that there is a class action lawsuit against them. We just want our money back and nothing more.
Asked by Nancy - Tue May 26 11:31:52 2009 - - 1 Answers - 0 Comments
A. You'll need to contact the firm handling the class action lawsuit and jump on board if you want to get your money back; most likely you won't recieve your entire invesmtent back, however if they settlement is in favor of the plaintiffs and the company has enough assets you might get most of it back. Best of luck!
Answered by Stephen - Tue May 26 20:46:24 2009
Q. My husband and I purchased a timeshare at Briggs Ranch in San Antonio 3 yrs ago and have been paying for it monthly. Last week we found out that the timeshare was never completed and that there is a class action lawsuit against them. We just want our money back and nothing more.
Asked by Nancy - Tue May 26 11:31:52 2009 - - 1 Answers - 0 Comments
A. You'll need to contact the firm handling the class action lawsuit and jump on board if you want to get your money back; most likely you won't recieve your entire invesmtent back, however if they settlement is in favor of the plaintiffs and the company has enough assets you might get most of it back. Best of luck!
Answered by Stephen - Tue May 26 20:46:24 2009
Is there a link between your horoscope sign and your Myers-Briggs Jung personality type?
Q. Is your Myers-Briggs - Jung personality type somehow related to your zodiac sign and the attributes ot your sign? Mine is for instance INTP and I'm an Aquarius sun, Scorpio rising and Capricorn moon.Are those somehow related? For instance, some traits of the signs would suggest that the majority of air signs are most likely to be extroverts and the water signs introverts. Any thoughts?
Asked by Sarafita - Thu Nov 5 18:00:21 2009 - - 7 Answers - 0 Comments
A. Myers-Briggs Jung is a psychological test. Astrology has to do with how a person thinks, behaves, and reacts to things, just based on astrological beings. Although they are not supposed to be interrelated, a lot of things can be linked together when talking about personalities of people. I'm an ISFP, Cancer sun, Cancer rising, and Aries moon. I'm also interested if anyone else has any links between the two. :)
Answered by Show - Thu Nov 5 18:29:50 2009
Q. Is your Myers-Briggs - Jung personality type somehow related to your zodiac sign and the attributes ot your sign? Mine is for instance INTP and I'm an Aquarius sun, Scorpio rising and Capricorn moon.Are those somehow related? For instance, some traits of the signs would suggest that the majority of air signs are most likely to be extroverts and the water signs introverts. Any thoughts?
Asked by Sarafita - Thu Nov 5 18:00:21 2009 - - 7 Answers - 0 Comments
A. Myers-Briggs Jung is a psychological test. Astrology has to do with how a person thinks, behaves, and reacts to things, just based on astrological beings. Although they are not supposed to be interrelated, a lot of things can be linked together when talking about personalities of people. I'm an ISFP, Cancer sun, Cancer rising, and Aries moon. I'm also interested if anyone else has any links between the two. :)
Answered by Show - Thu Nov 5 18:29:50 2009
how do you set timing on a 12 hp Briggs and Stratton?
Q. I am rebuilding a 12hp Briggs and Stratton Motor. It is single cylinder. I need to know how to time it. Can anyone tell me if you have to time it or how to time it. Thanks in advance.
Asked by sunkissed_babe1606 - Tue Sep 8 21:41:35 2009 - - 2 Answers - 0 Comments
A. , timing wise, when its disassembled, there should be a mark on both the camshaft gear, and the crankshaft gear, shaped like a little triangle or tear drop, they should be aligned on top of crank to bottom of cam, i e,, like a colon on the key board ( : ) what will also help, is to checkout a copy of small engine repair from the library i think manual is from haynes after the engine assembled, as far as running smooth you'll have to adjust the carb
Answered by ideal22us - Tue Sep 8 22:06:07 2009
Q. I am rebuilding a 12hp Briggs and Stratton Motor. It is single cylinder. I need to know how to time it. Can anyone tell me if you have to time it or how to time it. Thanks in advance.
Asked by sunkissed_babe1606 - Tue Sep 8 21:41:35 2009 - - 2 Answers - 0 Comments
A. , timing wise, when its disassembled, there should be a mark on both the camshaft gear, and the crankshaft gear, shaped like a little triangle or tear drop, they should be aligned on top of crank to bottom of cam, i e,, like a colon on the key board ( : ) what will also help, is to checkout a copy of small engine repair from the library i think manual is from haynes after the engine assembled, as far as running smooth you'll have to adjust the carb
Answered by ideal22us - Tue Sep 8 22:06:07 2009
How do you connect governor springs on a Briggs & Stratton lawnmower?
Q. Looking for a diagram on how to connect the governor springs on my Briggs & Stratton lawnmower engine
Asked by James B - Sat Mar 14 18:29:44 2009 - - 1 Answers - 0 Comments
A. Its very simple,follow your throttle cable from the top to where it connects to the carbeurator.It should be mounted on a swivel plate, the plate contains an extra small hole , that is where the gov. spring connects.Be sure you have the proper spring, or it may not open up as it supposed to,or shut off as needed.THe carb. housing may also be covered by a plastic cover,or guard.This is a simple do -it -yourselfer.Or go to b and stratton .com for tech support
Answered by unknown - Sat Mar 14 18:48:25 2009
Q. Looking for a diagram on how to connect the governor springs on my Briggs & Stratton lawnmower engine
Asked by James B - Sat Mar 14 18:29:44 2009 - - 1 Answers - 0 Comments
A. Its very simple,follow your throttle cable from the top to where it connects to the carbeurator.It should be mounted on a swivel plate, the plate contains an extra small hole , that is where the gov. spring connects.Be sure you have the proper spring, or it may not open up as it supposed to,or shut off as needed.THe carb. housing may also be covered by a plastic cover,or guard.This is a simple do -it -yourselfer.Or go to b and stratton .com for tech support
Answered by unknown - Sat Mar 14 18:48:25 2009
Is it possible to install a turbo charger on a briggs and stratton 10hp lawn mower engine?
Q. i have a 1976 wheel horse with a 10 hp briggs and stratton and i was wondering if i could get a turbo to bolt up to it and how hard it would be to plum the lines and get it set right.
Asked by 1950BUICKSPECIAL - Tue Mar 24 15:35:20 2009 - - 3 Answers - 0 Comments
A. I'm sure it's possible to build something to fit, but I don't think that the engine will put out enough exhaust pressure to turn the turbine fast enough to give you any benefit, also your engine is probably fairly high compression so you may overboost it, if it does work.
Answered by sixpak666666 - Tue Mar 24 15:44:15 2009
Q. i have a 1976 wheel horse with a 10 hp briggs and stratton and i was wondering if i could get a turbo to bolt up to it and how hard it would be to plum the lines and get it set right.
Asked by 1950BUICKSPECIAL - Tue Mar 24 15:35:20 2009 - - 3 Answers - 0 Comments
A. I'm sure it's possible to build something to fit, but I don't think that the engine will put out enough exhaust pressure to turn the turbine fast enough to give you any benefit, also your engine is probably fairly high compression so you may overboost it, if it does work.
Answered by sixpak666666 - Tue Mar 24 15:44:15 2009
why is my briggs and stratton keep poping black soot out the exhaust and the mower is very vibraty?
Q. i have put some briggs & stratton fuel stabliser in the fuel and thats when it started to pop little clouds of black smoke out the exhause every few seconds when the engine revs up thanks hope someone can help me out
Asked by ashley.sheppard2 - Sat Jun 28 08:47:13 2008 - - 6 Answers - 0 Comments
A. Probably needs servicing
Answered by wadeypops - Sat Jun 28 08:51:10 2008
Q. i have put some briggs & stratton fuel stabliser in the fuel and thats when it started to pop little clouds of black smoke out the exhause every few seconds when the engine revs up thanks hope someone can help me out
Asked by ashley.sheppard2 - Sat Jun 28 08:47:13 2008 - - 6 Answers - 0 Comments
A. Probably needs servicing
Answered by wadeypops - Sat Jun 28 08:51:10 2008
From Yahoo Answer Search: 'briggs'
Mon Sep 6 15:19:21 2010 [ refresh local cache ]
[Hide]▼
dailyherald.com
Wed, 25 Aug 2010 02:01:15 GMT+00:00
Chicago Daily Herald No worries: Weak-side linebacker Lance Briggs said he didn't have time to worry when Brian Urlacher went down with a calf injury early in the game last ... Tinoisamoa Likely Wins Job by Default Chicago Bear Report (subscription)
youtube.com
Sun, 10 May 2009 20:14:13 PDT
The Briggs @ Key Club music saves lives hollywood, California April 30, 2009 Directed By: punkvideosrock filmed By: Robert & Alberto Herrera ... youtube.com.
gossipblender.com
TV Rss.xml News from Female First
Fri, 27 Aug 2010 12:00:49 GM
The latest gossip and news written in the TV Rss.xml News from Female First reports... British actor Nick . Briggs. is to portray former British Prime Minister Winston Churchill in the 'Doctor Who Live' stage show. Nick . Briggs. is to port. ...
[Hide]▲
