Is there an alternative for using hydrostatic transmission fluid?
Q. This guy i know has a lawnmower with a hydrostatic transmission and was wandering if you can put anything else other than hydrostatic transmission fluid in it because the fluid is very expensive, any cheaper alternatives? He's put automatic gearbox oil in it, will it still work.
Asked by Walnut - Tue Nov 18 00:25:44 2008 - - 1 Answers - 0 Comments
A. regular transmission fluid will do fine . i add some heavy oil to it just for consistency . have cub cadet . big 50 in deck . my cadalac of the mow shack .
Answered by sexy_naughty_bitchy_me_40 - Tue Nov 18 01:10:31 2008
Q. This guy i know has a lawnmower with a hydrostatic transmission and was wandering if you can put anything else other than hydrostatic transmission fluid in it because the fluid is very expensive, any cheaper alternatives? He's put automatic gearbox oil in it, will it still work.
Asked by Walnut - Tue Nov 18 00:25:44 2008 - - 1 Answers - 0 Comments
A. regular transmission fluid will do fine . i add some heavy oil to it just for consistency . have cub cadet . big 50 in deck . my cadalac of the mow shack .
Answered by sexy_naughty_bitchy_me_40 - Tue Nov 18 01:10:31 2008
how to rebuild hydrostatic transmission on a lawn mower?
Q. I am looking for parts and information on rebuilding a hydrostatic transmission on a Murray 46-inch lawn mower. Problem is that when the unit warms up, it slows down, and barely goes in reverse. New belt didn't help. I never changed the fluid.
Asked by natureguyusa - Wed May 3 21:16:09 2006 - - 2 Answers - 0 Comments
A. You're going to need some help there, I wouldn't know where to start myself.
Answered by CottonPatch - Wed May 3 21:20:02 2006
Q. I am looking for parts and information on rebuilding a hydrostatic transmission on a Murray 46-inch lawn mower. Problem is that when the unit warms up, it slows down, and barely goes in reverse. New belt didn't help. I never changed the fluid.
Asked by natureguyusa - Wed May 3 21:16:09 2006 - - 2 Answers - 0 Comments
A. You're going to need some help there, I wouldn't know where to start myself.
Answered by CottonPatch - Wed May 3 21:20:02 2006
Hydrostatic Transmission in a LT 1018 Cub Cadet?
Q. We recentlly purchased a LT 1018 Cub Cadet, we have two questions about the Hydrostatic Transmission. 1: How do we check the fluid, and 2: What fluid does it take. Whoever answers correctlly first will get ten points if they want it. Please only answer if you know, no guesses. Thanks.
Asked by Beast O - Sat Jul 26 16:30:47 2008 - - 1 Answers - 0 Comments
A. There is a resivior that hold all the hyd.Oil for the drive sys. follow the hyd.Lines from the hydrstats and you'Ll find it,Might better ck the owners man. for the type of fld. or go on line to the int'L web site.
Answered by D2 - Sat Jul 26 16:37:04 2008
Q. We recentlly purchased a LT 1018 Cub Cadet, we have two questions about the Hydrostatic Transmission. 1: How do we check the fluid, and 2: What fluid does it take. Whoever answers correctlly first will get ten points if they want it. Please only answer if you know, no guesses. Thanks.
Asked by Beast O - Sat Jul 26 16:30:47 2008 - - 1 Answers - 0 Comments
A. There is a resivior that hold all the hyd.Oil for the drive sys. follow the hyd.Lines from the hydrstats and you'Ll find it,Might better ck the owners man. for the type of fld. or go on line to the int'L web site.
Answered by D2 - Sat Jul 26 16:37:04 2008
how does a hydrostatic transmission work in a lawnmower?
Q. I work at Lowes Hardware and i sell lawnmowers. i have many peopla ask how one works and i am not really sure. I know that it uses fluids but other than that, im not really sure.
Asked by dixie_boysles - Mon Mar 19 09:33:25 2007 - - 2 Answers - 0 Comments
A. It depends on what it says. An "Automatic" is an adjustment of the tension on the drive belt. In a hydro, you are controlling the flow of oil with a valve.
Answered by Todd B - Mon Mar 19 09:51:36 2007
Q. I work at Lowes Hardware and i sell lawnmowers. i have many peopla ask how one works and i am not really sure. I know that it uses fluids but other than that, im not really sure.
Asked by dixie_boysles - Mon Mar 19 09:33:25 2007 - - 2 Answers - 0 Comments
A. It depends on what it says. An "Automatic" is an adjustment of the tension on the drive belt. In a hydro, you are controlling the flow of oil with a valve.
Answered by Todd B - Mon Mar 19 09:51:36 2007
my hydrostatic transmission starts to smoke when its running for a while and wont move?
Q. sears craftsman 21.5 hp the rider is only 7 years old it has not been abused but it has been used a lot
Asked by 70zio - Sun Oct 7 16:11:28 2007 - - 2 Answers - 0 Comments
A. The Craftsman Hydrostatic trans-axle is a completely non-serviceable unit. If it gives any problems replacement is the only option. Sorry! You can go to www3.sears.com input your model number to bring up your mower, find and price the trans-axle to see if repair is worth it to you. This price will be for parts only, this site can not include installation labor.
Answered by Bart S - Sun Oct 7 16:32:01 2007
Q. sears craftsman 21.5 hp the rider is only 7 years old it has not been abused but it has been used a lot
Asked by 70zio - Sun Oct 7 16:11:28 2007 - - 2 Answers - 0 Comments
A. The Craftsman Hydrostatic trans-axle is a completely non-serviceable unit. If it gives any problems replacement is the only option. Sorry! You can go to www3.sears.com input your model number to bring up your mower, find and price the trans-axle to see if repair is worth it to you. This price will be for parts only, this site can not include installation labor.
Answered by Bart S - Sun Oct 7 16:32:01 2007
What type of tranny fluid is used in a Murray hydrostatic transmission ?
Q. What type of tranny fluid is used in a Murray hydrostatic transmission ?
Asked by Kevin - Tue Sep 1 21:06:14 2009 - - 1 Answers - 0 Comments
A. Look in your owners manual or call the dealer where you bought the lawnmower.
Answered by mister ss - Wed Sep 2 20:39:46 2009
Q. What type of tranny fluid is used in a Murray hydrostatic transmission ?
Asked by Kevin - Tue Sep 1 21:06:14 2009 - - 1 Answers - 0 Comments
A. Look in your owners manual or call the dealer where you bought the lawnmower.
Answered by mister ss - Wed Sep 2 20:39:46 2009
what kind of oil do i put in a hydrostatic transmission?
Q. what kind of oil do i put in a hydrostatic transmission?
Asked by Daddy - Sun Dec 3 12:52:03 2006 - - 4 Answers - 0 Comments
A. whatever the manufactuer calls for.I have a tractor with a hydraulic system and a hydrostatic trans. ant the both use hydraulic oil. I would caution about what brand you use as some oils may deteriorate your seals. again go with manuf. recommendations.
Answered by peckerwud2 - Sun Dec 3 13:08:32 2006
Q. what kind of oil do i put in a hydrostatic transmission?
Asked by Daddy - Sun Dec 3 12:52:03 2006 - - 4 Answers - 0 Comments
A. whatever the manufactuer calls for.I have a tractor with a hydraulic system and a hydrostatic trans. ant the both use hydraulic oil. I would caution about what brand you use as some oils may deteriorate your seals. again go with manuf. recommendations.
Answered by peckerwud2 - Sun Dec 3 13:08:32 2006
How do I change the transmission fluid in my lawn mower?
Q. Its a Yard Machine by mtd and about 8 years old. It kind of makes a squealing noise when i try to go foward and back ( its a hydrostatic transmission) But it goes pretty fast still but I think it would be better if i could change the fluid, I didnt see a plug but there is a rubber hose that comes off the top of the transmission thats about a foot long with a cap on the end of it.
Asked by rockstar510 - Fri Jun 5 15:43:33 2009 - - 1 Answers - 0 Comments
A. Without knowing the manufacturer and model it is difficult to answer your question. Do you still have your owners manual? This will often give service information that might give guidance. No owners manual. Try searching Yahoo with the manufacturer's name. Many have sites that include a manual you can download. Hope this helps a little.
Answered by Robert - Fri Jun 5 16:08:12 2009
Q. Its a Yard Machine by mtd and about 8 years old. It kind of makes a squealing noise when i try to go foward and back ( its a hydrostatic transmission) But it goes pretty fast still but I think it would be better if i could change the fluid, I didnt see a plug but there is a rubber hose that comes off the top of the transmission thats about a foot long with a cap on the end of it.
Asked by rockstar510 - Fri Jun 5 15:43:33 2009 - - 1 Answers - 0 Comments
A. Without knowing the manufacturer and model it is difficult to answer your question. Do you still have your owners manual? This will often give service information that might give guidance. No owners manual. Try searching Yahoo with the manufacturer's name. Many have sites that include a manual you can download. Hope this helps a little.
Answered by Robert - Fri Jun 5 16:08:12 2009
My Sears 42" Craftsman won't move. It has a hydrostatic transmission.?
Q. I replaced the drive belt but no success. Any suggestions.
Asked by Ted K - Thu Mar 12 13:52:36 2009 - - 6 Answers - 0 Comments
A. Don't forget about the lever on the back that you pull out and push in to put tractor in the mode to manually push it or use the hydor transmission. It may be stuck in the manual mode. I also noticed one time I was running my tractor around in circles as I was using a roller tine attachment to rough up lawn to plant grass seed. After about 1/2 hr of this, my tractor would not move either. Apparently I had forced transmission fluid out of the breather tube when I was driving around in those tight circles. I put some fluid back in and it was fine.
Answered by Tedruski - Fri Mar 13 12:02:29 2009
Q. I replaced the drive belt but no success. Any suggestions.
Asked by Ted K - Thu Mar 12 13:52:36 2009 - - 6 Answers - 0 Comments
A. Don't forget about the lever on the back that you pull out and push in to put tractor in the mode to manually push it or use the hydor transmission. It may be stuck in the manual mode. I also noticed one time I was running my tractor around in circles as I was using a roller tine attachment to rough up lawn to plant grass seed. After about 1/2 hr of this, my tractor would not move either. Apparently I had forced transmission fluid out of the breather tube when I was driving around in those tight circles. I put some fluid back in and it was fine.
Answered by Tedruski - Fri Mar 13 12:02:29 2009
how to add fluid to transmission on cub cadet hydrostatic sealed transmission?
Q. have cub cadet zero radius turn mower 22hp kohler, 50 inch deck
Asked by MICHAEL W - Tue Apr 6 20:26:35 2010 - - 2 Answers - 0 Comments
A. Hi Michael, You didn't state what model you have, so I'm forced to guess! I THINK you have Model # RZT 50 Zero Turn Rider. Check out this link. Here is where you can get your manual on-line. You'll need to know your Model # as well as the Serial # to get the correct manual. This link will allow you to click on a "locator" page if you're not sure where to find your numbers. Oh, and NEVER fill a hydraulic system through the vent!!! Fair Winds nad Smooth Sailing, -Jim-
Answered by Jim W. - Tue Apr 6 21:17:37 2010
Q. have cub cadet zero radius turn mower 22hp kohler, 50 inch deck
Asked by MICHAEL W - Tue Apr 6 20:26:35 2010 - - 2 Answers - 0 Comments
A. Hi Michael, You didn't state what model you have, so I'm forced to guess! I THINK you have Model # RZT 50 Zero Turn Rider. Check out this link. Here is where you can get your manual on-line. You'll need to know your Model # as well as the Serial # to get the correct manual. This link will allow you to click on a "locator" page if you're not sure where to find your numbers. Oh, and NEVER fill a hydraulic system through the vent!!! Fair Winds nad Smooth Sailing, -Jim-
Answered by Jim W. - Tue Apr 6 21:17:37 2010
I drove a Ingersoll Rand BL-275 and the transmission seemed to make a whining sound when moving forward?
Q. It did not make this noise in reverse. This was a backhoe that I went to look at on Craigslist, and I do not own it. I was just wondering what might be causing the noise? I know that the transmission is hydrostatic. Thank you for looking.
Asked by rufus - Sat Jul 4 08:19:47 2009 - - 1 Answers - 0 Comments
A. Hydrostats are a little noisier than others, but since you noticed a difference between forward and reverse, says something's not right. It could be a pump either cavitating from wrong hydraulic oil or filter plug up, or just wear. There should be a test port, on the control valve for hydraulic pressure, which you could monitor with a test gauge, looking for needle bounce when it's under load and hot, with a noticeable jump. Unless the price is really great, think a bit before you purchase it, because these babies are a little pricey to overhaul. My question would be, why is it up for sale?
Answered by Old-guy64 - Sat Jul 4 08:51:25 2009
Q. It did not make this noise in reverse. This was a backhoe that I went to look at on Craigslist, and I do not own it. I was just wondering what might be causing the noise? I know that the transmission is hydrostatic. Thank you for looking.
Asked by rufus - Sat Jul 4 08:19:47 2009 - - 1 Answers - 0 Comments
A. Hydrostats are a little noisier than others, but since you noticed a difference between forward and reverse, says something's not right. It could be a pump either cavitating from wrong hydraulic oil or filter plug up, or just wear. There should be a test port, on the control valve for hydraulic pressure, which you could monitor with a test gauge, looking for needle bounce when it's under load and hot, with a noticeable jump. Unless the price is really great, think a bit before you purchase it, because these babies are a little pricey to overhaul. My question would be, why is it up for sale?
Answered by Old-guy64 - Sat Jul 4 08:51:25 2009
Weed Eater 14.5hp Hydrostatic lawn tractor transmissiom?
Q. Weed Eater 14.5hp Hydrostatic lawn tractor transmission will not go into gear or anything its not tight..its like its in neutral it must be casue i can push it around...it will not go in to any gear or anything tis not tight i can move it just fine but doesnt go in o gear..something must be wrong in the transmission what is it?
Asked by mgleboff - Tue May 13 20:35:09 2008 - - 2 Answers - 0 Comments
A. I would first take a look at the linkage to see if it has become disconnected before I started tinkering with the transmission. It may save you a lot of time and money. Just follow the linkage from the shift lever to the tranny and see if all is connected and moves when you shift the lever. If so, then you may have transmission problems. Good luck.
Answered by eagle - Tue May 13 21:16:12 2008
Q. Weed Eater 14.5hp Hydrostatic lawn tractor transmission will not go into gear or anything its not tight..its like its in neutral it must be casue i can push it around...it will not go in to any gear or anything tis not tight i can move it just fine but doesnt go in o gear..something must be wrong in the transmission what is it?
Asked by mgleboff - Tue May 13 20:35:09 2008 - - 2 Answers - 0 Comments
A. I would first take a look at the linkage to see if it has become disconnected before I started tinkering with the transmission. It may save you a lot of time and money. Just follow the linkage from the shift lever to the tranny and see if all is connected and moves when you shift the lever. If so, then you may have transmission problems. Good luck.
Answered by eagle - Tue May 13 21:16:12 2008
where do i find a serial number and model number on an older mtd tractor?
Q. the mtd tractor has a pto driven mower deck, and is hydrostatic transmission. i need to find these numbers, so i can order parts. thanks for any help
Asked by jomarle55 - Sat Apr 12 15:50:30 2008 - - 1 Answers - 0 Comments
A. For you MTD tractor... Riding mower tags are located on the underside of the seat. You may also call MTD Customer Support at 1-800-800-7310 , Monday through Friday, 8:00am - 5:00pm EST.
Answered by Larry - Sat Apr 12 15:59:29 2008
Q. the mtd tractor has a pto driven mower deck, and is hydrostatic transmission. i need to find these numbers, so i can order parts. thanks for any help
Asked by jomarle55 - Sat Apr 12 15:50:30 2008 - - 1 Answers - 0 Comments
A. For you MTD tractor... Riding mower tags are located on the underside of the seat. You may also call MTD Customer Support at 1-800-800-7310 , Monday through Friday, 8:00am - 5:00pm EST.
Answered by Larry - Sat Apr 12 15:59:29 2008
How do you transfer a snowmobile motor onto a go-cart?
Q. I have a 1974 440 Panther. I plan on putting it on a go cart, but the motor has a hydrostatic transmission. How can i convert that over? I want to put it to a sprocket. any help will do though.
Asked by Brianna - Tue Mar 30 11:53:34 2010 - - 2 Answers - 0 Comments
Q. I have a 1974 440 Panther. I plan on putting it on a go cart, but the motor has a hydrostatic transmission. How can i convert that over? I want to put it to a sprocket. any help will do though.
Asked by Brianna - Tue Mar 30 11:53:34 2010 - - 2 Answers - 0 Comments
Hydrostatic Lawn Tractor question?
Q. I am looking at buying a mini Montgomery Wards tractor off craigslist. I plan on adding hyd. and a mini loader but i need it to go at least 10 to 12 mph i have been looking for the same thing with the 3 speed but i cant find any near Ramsey, MN. I was going to remove the engine drive pulley and just attach a larger pulley to get alittle more speed but i was wondering could i do the same to a hydrostatic transmission or would that just hurt it? If anybody knows how i could make it faster or where i could pick up a 3 speed 8hp Montgomery Wards tractor that would be great.
Asked by Jordan - Tue Jul 20 18:34:58 2010 - - 1 Answers - 0 Comments
A. The gearing in the hydrostatic transmission will not allow you to go any faster, no matter what engine or pulley you fit. I doubt you will get a transmission to fit without major work. XX
Answered by tonybradburyuk - Wed Jul 21 12:03:07 2010
Q. I am looking at buying a mini Montgomery Wards tractor off craigslist. I plan on adding hyd. and a mini loader but i need it to go at least 10 to 12 mph i have been looking for the same thing with the 3 speed but i cant find any near Ramsey, MN. I was going to remove the engine drive pulley and just attach a larger pulley to get alittle more speed but i was wondering could i do the same to a hydrostatic transmission or would that just hurt it? If anybody knows how i could make it faster or where i could pick up a 3 speed 8hp Montgomery Wards tractor that would be great.
Asked by Jordan - Tue Jul 20 18:34:58 2010 - - 1 Answers - 0 Comments
A. The gearing in the hydrostatic transmission will not allow you to go any faster, no matter what engine or pulley you fit. I doubt you will get a transmission to fit without major work. XX
Answered by tonybradburyuk - Wed Jul 21 12:03:07 2010
MTD lawn tractor with auto transmission quality?
Q. I am looking to by an MTD riding mower with an auto tranny(not hydrostatic). The owner says it works by increasing the tension on the drive belt to make the unit speed up. I know MTD has a spotty reputation, but I am mostly concerned about the auto drive system. Does anyone have any info on these mowers? Do they hold up well? Any problems?
Asked by Rob B - Sat Apr 12 20:14:23 2008 - - 1 Answers - 0 Comments
A. The AutoDrive system is not the best system for propelling a lawn tractor across the yard, but they do work. Provided you don't attempt to pull anything over 100 pounds (US) with it, and change both drive belts yearly. The tractor should outlive the deck by several years.
Answered by Bart S - Sat Apr 12 20:25:03 2008
Q. I am looking to by an MTD riding mower with an auto tranny(not hydrostatic). The owner says it works by increasing the tension on the drive belt to make the unit speed up. I know MTD has a spotty reputation, but I am mostly concerned about the auto drive system. Does anyone have any info on these mowers? Do they hold up well? Any problems?
Asked by Rob B - Sat Apr 12 20:14:23 2008 - - 1 Answers - 0 Comments
A. The AutoDrive system is not the best system for propelling a lawn tractor across the yard, but they do work. Provided you don't attempt to pull anything over 100 pounds (US) with it, and change both drive belts yearly. The tractor should outlive the deck by several years.
Answered by Bart S - Sat Apr 12 20:25:03 2008
SAE 20W is an oil, what kind of oil is it and what are it's applications?
Q. I know it is used in a hydrostatic transmission, but what does it specifically compare to? Hydraulic oil, engine oil, etc? Specifications?
Asked by chickad1974 - Wed Apr 11 11:39:29 2007 - - 4 Answers - 0 Comments
A. 20w 50 oil for cars a derivitive of fossil fuels uno oil outta the ground
Answered by ivonna - Wed Apr 11 11:45:48 2007
Q. I know it is used in a hydrostatic transmission, but what does it specifically compare to? Hydraulic oil, engine oil, etc? Specifications?
Asked by chickad1974 - Wed Apr 11 11:39:29 2007 - - 4 Answers - 0 Comments
A. 20w 50 oil for cars a derivitive of fossil fuels uno oil outta the ground
Answered by ivonna - Wed Apr 11 11:45:48 2007
anybody know anything about woods mow n machines?
Q. I have a model 6215 and I am trying to find out what kind of hydrostatic transmissions it has. ultimately i'd like to find an exploded diagram to th hydo anybody know where i can find this info?
Asked by Jarrett S - Thu Oct 30 22:21:58 2008 - - 1 Answers - 0 Comments
A. Clean off the transmission and find the tag or the imprint on the transmission that identifies the transmission and manufacturer. Do a Google search for the manufacturer and use the ID numbers to locate your transmission.
Answered by David L - Thu Oct 30 22:37:12 2008
Q. I have a model 6215 and I am trying to find out what kind of hydrostatic transmissions it has. ultimately i'd like to find an exploded diagram to th hydo anybody know where i can find this info?
Asked by Jarrett S - Thu Oct 30 22:21:58 2008 - - 1 Answers - 0 Comments
A. Clean off the transmission and find the tag or the imprint on the transmission that identifies the transmission and manufacturer. Do a Google search for the manufacturer and use the ID numbers to locate your transmission.
Answered by David L - Thu Oct 30 22:37:12 2008
Where to find SE, CC, or CD classification engine oil?
Q. My John Deere mower has the hydrostatic transmission, and is low on fluid. The manual says "SAE 10W30 engine oil with API classifications of SE, CC, or CD is recommended in the transmission." That's all great, but I can't find such oil at any of the local auto parts stores, and the guys working at the stores know nothing about it. Home Depot sells Deere, but the local HD doesn't have such oil either. (Nor does Lowe's.) Thank you for your help. -Dan 11 April update: I called my local Deere dealer yesterday. They service guys there said that the 10W30 I use in my engine would be just fine, as the SM classification is much better than the SE anyway. So as it turn out, the oil that comes in their standard service kit will work. Thank… [cont.]
Asked by vthoky - Sun Apr 9 15:59:28 2006 - - 3 Answers - 0 Comments
A. those classifications of oils were made to meet the requirements of the vehicles manufactured at the time. any 10w30 oil that you purchase will be far better than the oils you were looking for.new oil classifications come out every year or so and the old oils are obsolete. so dont worry any 10w30 will do.
Answered by nolmthug24 - Sun Apr 9 18:53:29 2006
Q. My John Deere mower has the hydrostatic transmission, and is low on fluid. The manual says "SAE 10W30 engine oil with API classifications of SE, CC, or CD is recommended in the transmission." That's all great, but I can't find such oil at any of the local auto parts stores, and the guys working at the stores know nothing about it. Home Depot sells Deere, but the local HD doesn't have such oil either. (Nor does Lowe's.) Thank you for your help. -Dan 11 April update: I called my local Deere dealer yesterday. They service guys there said that the 10W30 I use in my engine would be just fine, as the SM classification is much better than the SE anyway. So as it turn out, the oil that comes in their standard service kit will work. Thank… [cont.]
Asked by vthoky - Sun Apr 9 15:59:28 2006 - - 3 Answers - 0 Comments
A. those classifications of oils were made to meet the requirements of the vehicles manufactured at the time. any 10w30 oil that you purchase will be far better than the oils you were looking for.new oil classifications come out every year or so and the old oils are obsolete. so dont worry any 10w30 will do.
Answered by nolmthug24 - Sun Apr 9 18:53:29 2006
JD 185 Hydro what to use for hydrostatic-fluid ford type-f or 10W30?
Q. one of repair books says Ford type-F for the SundStrand transmission mod BDU-10 S-213 Ser# 88-07-15585 the jd operator's manual said the 10W30 Engine oil with does not sound right with sould i use fd type-F like the repair manual said or 10W30 with the JDeere operator's manual Said
Asked by GM - Fri Dec 7 08:35:41 2007 - - 1 Answers - 0 Comments
A. Oh, f**king cr*p thos old John Deere manuals I would go with atf d/m 3 or 4
Answered by General Lee 01 - Fri Dec 7 08:58:36 2007
Q. one of repair books says Ford type-F for the SundStrand transmission mod BDU-10 S-213 Ser# 88-07-15585 the jd operator's manual said the 10W30 Engine oil with does not sound right with sould i use fd type-F like the repair manual said or 10W30 with the JDeere operator's manual Said
Asked by GM - Fri Dec 7 08:35:41 2007 - - 1 Answers - 0 Comments
A. Oh, f**king cr*p thos old John Deere manuals I would go with atf d/m 3 or 4
Answered by General Lee 01 - Fri Dec 7 08:58:36 2007
From Yahoo Answer Search: 'hydrostatic transmission'
Mon Sep 6 19:49:32 2010 [ refresh local cache ]
[Hide]▼
ironsearch.com
Fri, 11 Jun 2010 00:00:00 PDT
HOURS, Fuel Type: Diesel; Separator Hours: 496; Drive Type: 2WD; Hydrostatic Transmission; Crop: Corn & Beans; Thrashing: AFX Rotor; Unloading ... ironsearch.com.
f1681.tequilamemoirs.com
admin
hu, 24 Jun 2010 22:59:02 GM
Husqvarna Garden Tractor. Best Deal on Husqvarna Garden Tractor, shop from 59 results starting at $10 ... All tractors feature . hydrostatic transmissions. for smooth, variable forward and reverse speed. ...
[Hide]▲
